Welcome to Melur.Online|Malaysia's Largest Home Improvement Online Street| Enjoy Free Shipping to Seremban and Klang Valley| Start shopping with us now!
adhesive (1)
Sort by
Show result
  • SURFACES MUST BE CLEAN, DRY AND THOROUGHLY ROUGHEN.
  • REMOVE CAPS, PIERCE END OF TUBES. SQUEEZE EQUAL AMOUNT OF RESIN AND HARDENER FROM EACH TUBE. RATIO 1:1
  • MIX THOROUGHLY UNTIL CONSISTENT CRYSTAL CLEAR COLOR MIXTURE.
  • APPLY TO THE SURFACES TO BE REPAIRED OR JOINED TOGETHER.
RM9.90
RM13.00
  • THOROUGHLY CLEANAND DRY SURFACE FROM OIL, DIRT AND GREASE WITH MINERAL TURPENYINE.
  • PIERCE SEAL IN TUBE BY INVERTING CAP AND PUSHING INTO TOP OF TUBE.
  • CUT NOZZLE AT 45° ANGLE AND FIT TO TUBE.
  • HOLD TUBE AT 45° ANGLE AND PUSH SEALANT AHEAD OF NOZZLE.
  • FOR A SMOOTH FINISH, TOOL WITH SPATULA. EXCESS SEALANT MUST BE CLEANED UP BEFORE THE SEALANT SKINS IN 5-10 MINUTES. WIPE EXCESS AWAY WITH A CLOTH DAMPENED IN MINERAL TURPENTINE.
  • SEALANT WILL CURE FULLY IN 48 HOURS. AT THIS POINT ANY UNNEEDED SEALANT CAN BE REMOVED BY TRIMMING WITH A SHARP BLADE, BUT AVOID UNDER-CUTTING SEAL.
  • AFTER USE REMOVE NOZZLE AND REPLACE CAP.
RM11.60
RM14.00
  • ENSURE SURFACES ARE CLEAN, DRY AND FREE FROM DIRT OR GREASE. REMOVE CAP AND CAREFULLY PIERCE DIAPHRAGM.
  • SQUEEZING GENTLY, APPLY TO BOTH SURFACES AND SPREAD EVENLY. PRESS SURFACES TOGETHER AND CLAMP OR HOLD FIRMLY FOR APPROXIMATELY 1-2 MINUTES OR UNTIL ADHESIVE GRABS. INSTANT BONDS CAN BE ACHIEVED ON CONTACT BY WAITING APPROXIMATELY 1 MINUTE BEFORE PRESSING PARTS TOGETHER FIRMLY.
  • ALLOW APPROXIMATELY 10-12 HOURS FOR DRYING TO ACHIEVE STRENGTH SUFFICIENT FOR NORMAL USE. MAXIMUM BOND STRENGTH IS ACHIEVE AFTER 24 HOURS OR LONGER IF LARGE AREAS OR NON-POROUS MATERIAL (E.G. PVC) ARE BEING BONDED.
  • AFTER APPLICATION CLEAN NOZZLE AND REPLACE CAP. ANY SPILLS CAN BE REMOVED WITH ACETONE (FOUND IN SOME NAIL POLISH REMOVERS).
RM14.30
RM16.00
  • SURFACES TO BE REPAIRED SHOULD BE CLEAN, DRY AND FREE FROM GREASE. FOR THE BEST ADHESION, SCRAPE AND SAND THE SURFACES AND CLEAN WITH ACETONE.
  • UNSCREW CAPS OF EACH TUBE AND PIERCE TUBE SEAL WITH REVERSE END OF OWN CAP TO AVOID CONTAMINATION.
  • DISPENSE EQUAL AMOUNT OF RESIN AND HARDENER (PARTS A & B) ONTO A CLEAN DISPOSABLE SURFACE AND MIX THOROUGHLY. THE MIXTURE WILL REMAIN USABLE FOR 3-4 MINUTES.
  • APPLY TO SURFACES TO BE REPAIRED AND ALLOW TO HARDEN
  • TO RESEAL, WIPE NOZZLES CLEAN AND REPLACE CAPS TO ORIGINAL TUBE (COLOUR CODED), OR HARDENING MAY OCCUR IN TUBE NOZZLE.
RM11.90
RM14.00
  • SURFACES TO BE REPAIRED SHOULD BE CLEAN, DRY AND FREE FROM GREASE. FOR BEST ADHESION, SCRAPE AND SAND THE SURFACES AND CLEAN WITH ACETONE.
  • UNSCREW CAPS OF EACH TUBE AND PIERCE TUBE SEAL WITH REVERSE END OF OWN CAP TO AVOID CONTAMINATION.
  • DISPENSE EQUAL AMOUNT OF RESIN AND HARDENER (PARTS A & B) ONTO A CLEAN DISPOSABLE SURFACE AND MIX THOROUGHLT. THE MIXTURE WILL REMAIN USABLE FOR 3-4 MINUTES.
  • APPLY TO SURFACES TO BE REPAIRED AND ALLOW TO HARDEN.
  • TO RESEAL, WIPE NOZZLES CLEAN AND REPLACE CAPS TO ORIGINAL TUBE (COLOUR CODED), OR HARDENING MAY OCCUR UN TUBE NOZZLE.
RM11.90
RM14.00
  • ENSURE SURFACES TO BE BONDED ARE CLEAN, DRY, FREE OF DUST AND CLOSE FITTING.
  • REMOVE NOZZLE AND PIERCE TUBE SEAL WITH REVERSE END OF CAP AND REPLACE NOZZLE.
  • REMOVE CAP AND APPLY A SMALL AMOUNT OF GLUE TO ONE SURFACE. BRING SURFACES TOGETHER AND APPLY SLIGHT PRESSURE. ALLOW 30 MINUTES FOR SUFFICIENT BOND STRENGTH FOR PRACTICAL USE. MAXIMUM BOND STRENGTH REACH AFTER 12 HOURS.
  • WIPE TIP OF TUBE, REPLACE CAP AND STORE UPRIGHT IN DRY COOL PLACE.
RM7.50
RM9.50
MYCYBERSALE ASIA 2019
#MYCYBERSALE is Malaysia’s Biggest Online Sale Event, an event that gathers Malaysia’s popular e-Tailers, selling at the same period.